Tool reference
Every tool of the toolbars and the header, in their order, with its icon. The pages linked from each group describe how the tools are used. Tools that share a button open beside the toolbar with a right-click, or a long press on a touch screen.
Sketch toolbar
Drawing (Drawing in a sketch)
Tool |
What it does |
|
|---|---|---|
Exit |
Closes the sketch and goes back to the tree. |
|
Select |
Picks, box-selects and drags. A right-click opens the relations of the selection. |
|
Profile |
Lines one after another, tangent arcs by pressing and dragging. |
|
Line |
A single line from its start to its end. |
|
Circle |
A circle by its center and a point on it. |
|
Arc |
An arc by its center, its start and its end. |
|
Rectangle |
A rectangle by two opposite corners. |
|
Centered rectangle |
A rectangle by its center and a corner. |
|
Oriented rectangle |
A rectangle by one side and a point on the opposite side. |
|
Polygon |
A regular polygon by its center and a corner. |
|
Hexagon |
A hexagon by its center and the middle of a flat. |
|
Oblong |
A slot by its center line and its width. |
|
Curved oblong |
A curved slot by its arc’s center, start and end, and its width. |
|
Keyhole |
A hole with a slot. |
|
Point |
A point, which stays on the element it is placed on. |
|
Spline |
A smooth curve through points. |
|
B-spline |
A curve by its control points. |
|
Connect |
A smooth curve between the ends of two elements. |
|
Curve |
A curve from the formulas h(t) and v(t). |
|
Construction |
Construction elements, drawn dashed, which are no part of faces and files. |
|
Project |
Edges of other sketches and earlier results as fixed references. |
Constraints and measuring (Constraints and dimensions, Measuring)
Tool |
What it does |
|
|---|---|---|
Dimension |
A length, distance, angle, radius or diameter, placed by a click. |
|
Measure |
Lengths and distances, or the whole sketch. |
|
Constraints |
The relations of the selection. |
|
Rigid group |
The selected elements as one rigid body. |
Editing (Editing a sketch)
Tool |
What it does |
|
|---|---|---|
Fillet |
Rounds a corner, or every corner of a chain. |
|
Chamfer |
Cuts a corner by one or two lengths, or a length and an angle. |
|
Quick trim |
Cuts away the piece under the click. |
|
Trim to |
Cuts pieces away at a chosen element. |
|
Split |
Cuts elements into pieces where they meet a cutter. |
|
Mirror |
Mirrors the selection about a line or axis. |
|
Offset |
Draws an element or a chain at a distance. |
|
Circular pattern |
Copies the selection around a center. |
|
Linear pattern |
Copies the selection in a row or a grid. |
|
Delete |
Removes the selection. |
|
Undo |
Steps back. |
|
Redo |
Steps forward again. |
|
Fit |
Shows the whole sketch. |
Design toolbar
Sketches and faces (The Design tree)
Tool |
What it does |
|
|---|---|---|
New sketch |
Starts a sketch. |
|
Face |
The closed regions of a sketch as a face. |
|
Wire |
A chain of a sketch’s elements. |
Combining (The Design tree)
Tool |
What it does |
|
|---|---|---|
Fuse |
Unites faces. |
|
Subtract |
Cuts the later faces from the first. |
|
Intersect |
Keeps the common part of faces. |
|
Symmetric difference |
Keeps where exactly one of the faces lies. |
|
Glue |
Faces and wires as one shape, every overlap a face of its own. |
|
Split |
Cuts a result into pieces where a cutter crosses it. |
|
Trim |
Cuts a result with a cutter and keeps or removes pieces by its rule. |
Shaping and placing (The Design tree)
Tool |
What it does |
|
|---|---|---|
Offset |
Grows or shrinks faces, or offsets wires. |
|
Fillet |
Rounds corners of a face or a wire. |
|
Chamfer |
Cuts corners of a face or a wire. |
|
Defeature |
Closes gaps, removes small edges, merges lines and fits arcs and splines. |
|
Mirror |
Mirrors a result about a line. |
|
Move |
Shifts a result. |
|
Rotate |
Turns a result about a center. |
|
Linear pattern |
Copies in a row or a grid. |
|
Circular pattern |
Copies around a center. |
Simulations (Simulations), the first on the button, the others beside it
Tool |
What it does |
|
|---|---|---|
Stress analysis |
A plane-stress analysis of the selected result. |
|
Plate frequencies |
The natural frequencies of the selected result as a plate. |
|
Heat transfer |
Temperatures and heat flow in the selected result. |
|
Electrostatics |
The electric field and the capacitance of the selected result. |
|
Magnetics |
The magnetic field, forces and inductance of the selected result. |
|
Beam calculator |
A beam with the selected result as its cross-section. |
Drawings (Drafting), the first on the button, the other beside it
Tool |
What it does |
|
|---|---|---|
Drafting on a new page |
Puts the selected result on a new page of the drawing. |
|
Drafting on the current page |
Adds the selected result to the page open in Drafting. |
Measuring, properties and parameters (Measuring, Properties, Constraints and dimensions)
Tool |
What it does |
|
|---|---|---|
Measure |
Area, centroid, second moments, lengths and distances. |
|
Properties |
Names, colors and mesh sizes of faces and edges. |
|
Parameters |
Named values for dimensions and formulas. |
|
Delete |
Removes the selected operations. |
|
Undo |
Steps back. |
|
Redo |
Steps forward again. |
|
Fit |
Shows everything. |
Simulation workbench
The toolbar of a simulation’s workbench (Simulations). The tools between Update and Delete are the items of the simulation’s type, in the order of its tree, and each opens its popup.
Tool |
What it does |
|
|---|---|---|
Exit |
Closes the workbench and goes back to Design. |
|
Select |
Picks rows and chips in the view, and closes the open popup. |
|
Update |
Solves again with the current settings. A dot marks a simulation out of date. |
|
Material |
Young’s modulus, Poisson’s ratio, yield strength or density (stress, plate). |
|
Model |
Cross-section or plate, planar or axisymmetric, length or thickness (heat, electrostatics, magnetics). |
|
Beam |
Length, material and the beam’s own weight (beam). |
|
Regions |
The material of each region, and its heat input (heat, electrostatics, magnetics). |
|
Magnets |
Remanence and direction of each magnet region (magnetics). |
|
Circuits |
The currents of the windings (magnetics). |
|
Windings |
A region wound on a circuit, with its turns (magnetics). |
|
Supports |
Fixed, clamped, simply supported or pinned places (stress, plate, beam). |
|
Loads |
Forces, pressures and bolt loads, or the loads along a beam (stress, beam). |
|
Boundary conditions |
Temperatures, heat inputs, convection, radiation and contact resistances (heat). |
|
Conductors and charges |
Voltages, floating conductors and surface charges (electrostatics). |
|
Flux parallel |
Edges the flux runs along (magnetics). |
|
Measurements |
Values at points and along edges, and the simulation’s own measurements. |
|
Solver |
Thickness or element order, accuracy estimate, open space, transient, Simplify outline. |
|
Results |
The full results, the color scale and its range, Report PDF and CSV. |
|
Modes |
The natural frequencies, the report (plate). |
|
Delete |
Removes the selected row. |
|
Undo |
Steps back in the simulation’s settings. |
|
Redo |
Steps forward again. |
|
Fit |
Shows the whole part. |
Drafting workbench
The toolbar of Drafting (Drafting). A tool goes back to Select after one use, and a double-click keeps it on until Esc.
Tool |
What it does |
|
|---|---|---|
Select |
Picks and drags dimensions, views and tables. A double-click opens a dimension’s popup or a view’s settings. |
|
New page |
Adds an empty page with the settings of the page before it. |
|
New view |
Puts a view of a Design result or a STEP part on the open page. |
|
Open STEP |
Reads a 3D part from a STEP file into the drawing. |
|
Dimension |
Adds a dimension by hand: a length, a distance, a radius, a diameter or an angle. |
|
Automatic dimensions |
Dimensions the selected views, or every view of the page, and takes the dimensions off again. |
|
Center lines |
Changes the center lines of a circle or an arc. |
|
Axis |
Draws a center line between two points. |
|
Table |
Puts a table on the page, such as a parts list. |
|
Update |
Takes the current geometry of Design into the views of Design results. |
|
Page settings |
Sheet, orientation, standard, scale, frame and title block of the open page. |
|
Delete |
Removes the selection, or hides an automatic dimension. |
|
Undo |
Steps back. |
|
Redo |
Steps forward again. |
|
Fit |
Shows the whole page. |
Dimension popup
The buttons of a dimension’s popup, which opens with a double-click on the dimension. The popup shows the rows that fit the dimension.
Button |
What it does |
|
|---|---|---|
True length, aligned |
A length at its true length, or a distance along the line through its two points. |
|
Horizontal |
The horizontal distance. |
|
Vertical |
The vertical distance. |
|
Radius |
A circle or an arc by its radius. |
|
Diameter |
A circle or an arc by its diameter. |
|
Middle |
A length’s value above the middle of its line. Beyond the start, beyond the end and on a leader follow later. |
|
n× from the sketch |
The number of equal features before the value, from the sketch’s patterns. |
|
No count |
The value alone. |
|
As the layout chooses |
A diameter through the circle where its value fits, on a leader where it does not. |
|
Through the center |
The dimension line through the center, the value inside the circle. |
|
On a leader |
The value on a leader out of the part, bent to a horizontal line. |
|
Across, from outside |
Two extension lines touching the circle and a dimension line between them, like a length. |
|
As the layout chooses |
A radius inside its arc where there is room, else outside. |
|
Inside |
The arrow and the value on the center’s side of the arc. |
|
Outside |
The arrow and the value outside the arc. |
|
On a leader |
The value on a leader out of the part. |
|
The angle |
The angle as measured. |
|
Its supplement |
180° less the angle, the arc on the other side of a leg. |
|
Text |
Written in place of the value, such as M5 for a thread. |
|
After it |
Written after the value, such as EQS. |
Header
Button |
What it does |
|
|---|---|---|
Design, Drafting |
Switch between the part’s tree and the drawing. See Drafting. |
|
Report a bug |
Reports a bug with your message, and with the current geometry if you include it. |
|
New |
Starts an empty part. See Files. |
|
Open |
Opens a .pxe2d project file. See Files. |
|
Save |
Saves the part as a .pxe2d project file. See Files. |
|
Save as |
Writes DXF, SVG, STEP or BREP, or the PDF report of a simulation. See Files. |
|
Import |
Reads a DXF, SVG, STEP or BREP file into the tree. See Files. |
Docs opens these pages in a new tab. In the frame of the tool page, the icon at the right end of the header opens the editor on its own page, with the part saved first, so it is there on the new page.